450 GSM carbon Fiber Specifications
|
|
|
| 450-GSM Grade 1 Carbon Fiber |
|
|
| Technical Specifications |
|
|
| Weave Unidirectional |
|
|
| Width |
6in |
15.24cm
|
|
Typical Dry Properties:
|
|
|
| Max length Roll |
164ft
|
50m
|
| Tensile Strength |
5800
|
Mpa
|
| Tensile Elastic Modulus |
255.53
|
Gpa
|
| Elongation |
1.6
|
%
|
| Laminated Fiber Properties |
|
|
| Tensile Strength: ASTM D3039 |
4840
|
Mpa
|
| Tensile Elastic Modulus ASTM D3039 |
255.53
|
Gpa
|
| Elongation ASTM D3039 |
1.95
|
%
|
| Flexural Strength ASTM D7264 |
921
|
Mpa
|
| Shear Strength ASTM D2344 |
96
|
Mpa
|
| Density |
1.8g/
|
cm3
|
1 - 150ft long roll carbon fiber 450-GSM Uni-Directional fiber 6in wide
900mls /Av of Epoxy per 10ft ordered
Upgrade to 150ft and receive discounts
1-2- Roller, Head, tray & Rollers
1-2 - Square Trowels
Mixing Bucket+ - Gloves+
1 - Instructions Document
- Requires that you have grinding equipment to prepare and decontaminate the concrete surface before application.
450-GSM Uni-Directional Carbon Fiber Fabric Grade 1 (grams per square meter)6in Wide
450-GSM is perfect for Poured or Block walls with cracked walls or curved applications to prevent re-cracking.
Ideal for a contractor that generally use carbon fiber for concrete reinforcement. Unidirectional carbon provides the best carbon fiber application solution as it has the least elongation or stretch before fully loading. Woven Carbon fabric from others allows for much more movement of the concrete crack and joint thus may contribute to the failure of the intended repair. Account for a maximum spacing when reinforcing block or poured walls of 4 feet vertically or horizontally.
Applications of 450GSM 8 in Unidirectional Carbon Fiber
Reinforcement to Poured or Masonry Block walls
Use to form Carbon Fiber Wall Straps
Retaining walls
Reinforce exterior concrete corners
Reinforce foundation window openings or lintel
Use horizontally to bridge openings
Great for Poured Concrete Wall applications
Steps of Application of the Carbon Fiber
1. Prepare any wall cracks if a poured wall using Epoxy Crack Injection if a block wall re-tuckpoint any broken mortar joints.
2. Using a diamond cup wheel with a grinder and dust shroud, decontaminate the concrete surface and vacuum all dust off the concrete wall surface.
3. Layout carbon fiber on a clean surface to cut to the proper length as needed.
4. Mix the Startech Epoxy 2:1 ratio in a mixing cup
5. Apply some epoxy to the concrete surface approximately 6 in wide where the carbon fiber is to be installed using a trowel and roller. Also, roller one side of the carbon that is to be applied.
6. Apply the fabric to the concrete with the epoxy-coated side toward the wall, and using the roller supplied, roll the material while adding more epoxy.
7. At this point, using the square trowel supplied and using the flat side trowel, the epoxy into the fabric to work it into the Carbon Fiber Strap. Make sure that you have the carbon fabric held down so it does not move.
6. Re-roll the fabric to smooth out the epoxy and add more epoxy as needed.
Structural Epoxy for Carbon Fiber
Startech Hi-Modulus Fiber Matrix is a 100% solids, solvent-free, two-component MOISTURE INSENSITIVE EPOXY. Startech Fiber Matrix is a low-viscosity epoxy for wetting and use carbon fiber for structural repairs.
Epoxy Advantages
- Easy mix ratio: 2 Parts A to 1 Part B by Volume
- Long Pot Life with Rapid Strength Development
- Provides high early strength and excellent adhesion to most structural materials
- Insensitive to moisture before, during, and after cure
- Low-temperature cures - As low as 40oF (4oC)
PHYSICAL PROPERTIES
- Startech LPL Hi-Modulus Fiber Matrix is a 100% solids, solvent-free, two-component MOISTURE INSENSITIVE EPOXY. Startech Fiber Matrix is a low-viscosity epoxy for wetting and carbon fiber for structural repairs.
- Moisture Insensitive & low-temperature cure
- Nano Fiber Matrix Structural Epoxy
Category List
